If you shop at Amazon.com (for anything), use this link to support FordTaurus.net!

center console ?, also, service manual needed

Post Reply
penelhum
Regular Member
Posts: 22
Joined: Sun Jul 01, 2018 2:11 pm
Vehicle: 2013 PI

center console ?, also, service manual needed

Post by penelhum » Fri Aug 03, 2018 10:24 pm

I'm on a mission to install a center console myself. i have a 2013 interceptor and found a center console i need to pick up from a salvage yard. The first basic question is: there is a black metal plate running the center of my vehicle, between the front seats. I guess that's what was used to mount the lights, radio, and other law enforcement tools. Will i need that for a civilian center console or can i remove that metal plate?

I have not been able to find photos on this website, if anyone has photos of the process, that'd help me out. I know there are brackets that need to go with the console, other than that im lost at this time.

Does anyone have a service manual for 2013 and/or up to 2017 taurus in PDF format? I want to learn how to install/fix some of the items on my interceptor.

Thanks


mope
Regular Member
Posts: 130
Joined: Mon Oct 03, 2016 4:11 pm
Vehicle: 2013 Interceptor

Re: center console ?, also, service manual needed

Post by mope » Sat Aug 04, 2018 12:38 pm

iirc that plate comes out. youll bolt your console to the dash and then use the rear mounting holes on the trans tunnel for rear bolts.

MAKE SURE you get both the carpet filler panels below both sides of the console AND both sides of the trim pieces that run from top of console up to dash and have holes for key/trunk button. youll have to order the filler piece in the dash.....cant get that from the salvage car.

the pi has all the wiring youll need to run lights, usb, seat warmers etc. once you remove the lower dash cover

penelhum
Regular Member
Posts: 22
Joined: Sun Jul 01, 2018 2:11 pm
Vehicle: 2013 PI

Re: center console ?, also, service manual needed

Post by penelhum » Sat Aug 04, 2018 3:07 pm

That is a huge help, thanks.

penelhum
Regular Member
Posts: 22
Joined: Sun Jul 01, 2018 2:11 pm
Vehicle: 2013 PI

Re: center console

Post by penelhum » Mon Aug 06, 2018 9:21 pm

There is a panel under the radio, just near the gas pedal. its on both driver and passenger side. how is that panel removed? do i pry it off using a plastic trim removal tool or are there some screws that i missed? so far ive been able to remove panels but im stuck at this point.

Not sure if I have to remove the panel under the steering wheel, or whether i can just pry that panel off.
This should be the past piece before I attach my console.

see photos
Attachments
20180806_194804.jpg
20180806_194804.jpg (123.05 KiB) Viewed 847 times
20180806_194729.jpg
20180806_194729.jpg (109.64 KiB) Viewed 847 times

penelhum
Regular Member
Posts: 22
Joined: Sun Jul 01, 2018 2:11 pm
Vehicle: 2013 PI

Re: center console ?, also, service manual needed

Post by penelhum » Mon Aug 06, 2018 9:27 pm

secondary question, how do i remove the gear shift knob? i want to keep the "leather" surrounding the shifter but i want the shifter gone.
Attachments
shifter.jpg
shifter.jpg (118.28 KiB) Viewed 845 times

mope
Regular Member
Posts: 130
Joined: Mon Oct 03, 2016 4:11 pm
Vehicle: 2013 Interceptor

Re: center console ?, also, service manual needed

Post by mope » Tue Aug 07, 2018 3:24 pm

I did take the panel under wheel off, but cant remember if that was for my new footwell lighting or for that panel. There is a capture spring on the inside, can't make out what the lower fastener is. A hefty yank toward the back seats may be all you need.
Attachments
Capture.JPG
Capture.JPG (12.41 KiB) Viewed 810 times

penelhum
Regular Member
Posts: 22
Joined: Sun Jul 01, 2018 2:11 pm
Vehicle: 2013 PI

Re: center console ?, also, service manual needed

Post by penelhum » Fri Aug 10, 2018 10:25 pm

its been slow in these forums, dang.

took off the shift knob. polished the center console. tried to install but the current radio faceplate is not compatible with the console. the photos can explain better.

I'll be upgrading to an 8" screen and swapping out the radio faceplate to match the new screen, im sure that will be a headache in itself. never done any of this before. stay tuned
console3.jpg
console3.jpg (77.4 KiB) Viewed 754 times
console1213.jpg
console1213.jpg (123.24 KiB) Viewed 754 times

penelhum
Regular Member
Posts: 22
Joined: Sun Jul 01, 2018 2:11 pm
Vehicle: 2013 PI

Re: center console ?, also, service manual needed

Post by penelhum » Fri Aug 10, 2018 10:33 pm

removed the knob. some after pics.
hopefully i can get everything sorted out with a new radio next week. currently no bluetooth, no aux.

shift knob.jpg
shift knob.jpg (105.1 KiB) Viewed 753 times
consoleshine.jpg
consoleshine.jpg (91.96 KiB) Viewed 753 times

penelhum
Regular Member
Posts: 22
Joined: Sun Jul 01, 2018 2:11 pm
Vehicle: 2013 PI

Re: center console ?, also, service manual needed

Post by penelhum » Sun Aug 12, 2018 12:22 pm

so here is my other predicament. The wire from the vehicle does not match the wire from the center console. Is there an adapter I need to get or is that the wrong wire from the vehicle? I can't find another one in the vehicle.

I looked at all the write ups and i dont think this was mentioned. And i don't have a service manual

power.jpg
power.jpg (84.66 KiB) Viewed 713 times

mmsstar
Regular Member
Posts: 185
Joined: Sat Feb 14, 2009 11:48 am
Location: CLeveland Ohio Area
Vehicle: 2011 Flex SE

Re: center console ?, also, service manual needed

Post by mmsstar » Sun Aug 12, 2018 9:43 pm

Wrong wire from vehicle.

Saunders1986
Regular Member
Posts: 17
Joined: Sat Jul 07, 2018 10:30 pm

Re: center console ?, also, service manual needed

Post by Saunders1986 » Wed Aug 15, 2018 8:54 am

Strange the console do not fit radio faceplate, I have seen it done a number of times, first time I have ever herd of anyone having this issue?

uzi4life991
New Member
Posts: 3
Joined: Thu Sep 06, 2018 9:14 pm
Vehicle: 2013 3.5l ecoboost

Re: center console ?, also, service manual needed

Post by uzi4life991 » Tue Sep 11, 2018 8:07 pm

Bought same console pretty much out of a 2014 limited taurus and having the same issues.. did upgrading to the 8" radio/bezel solve your fitment issue? and did your connections work out fine with your original radios harnesses? Trying to decide if i should just buy the base sel radio bezel i found or attempt to install the 8" radio/bezel and the little controller for the unit. Appreciate any further info on how this went!
Also had same issues with center console harness not matching the card plug sadly same as the issue already pictured in this post. Lol wish this forum was more active!

mope
Regular Member
Posts: 130
Joined: Mon Oct 03, 2016 4:11 pm
Vehicle: 2013 Interceptor

Re: center console ?, also, service manual needed

Post by mope » Wed Sep 12, 2018 4:58 pm

re: console harness - it's been years since I did mine so take my memory with a grain of salt. The civi console harness (female) doesn't have a matching PI (male) harness. You just bypass that and wire in your electronics after tracing your wires. The console may well have the sync module/etc. that you can't use.

Saunders1986
Regular Member
Posts: 17
Joined: Sat Jul 07, 2018 10:30 pm

Re: center console ?, also, service manual needed

Post by Saunders1986 » Fri Sep 28, 2018 10:51 am

I just installed center console in my pi, and ran into the same problem with those trim pieces not fitting around the radio, I took some side cutters and simply cut those tabs off the trim part. I’m going to make a custom trim peice to close the gap below the heater controls
Attachments
7ED9ABB6-48E2-45D5-8AF6-C942623FFAAA.jpeg
7ED9ABB6-48E2-45D5-8AF6-C942623FFAAA.jpeg (89.74 KiB) Viewed 316 times

crownedking
Regular Member
Posts: 74
Joined: Fri Mar 18, 2016 1:03 pm
Location: MN
Contact:

Re: center console ?, also, service manual needed

Post by crownedking » Mon Oct 01, 2018 11:44 am

it looks better if you get the base LX face plate.
DON'T buy from paid PI mod sites, stay away from dealer programming! message me for help or questions.

"If you believe you can figure it out on your own then by all means do feel free to do so. I have nothing against people who want to do it on their own. I am not aware of anyone else that has done it though." - jmr061 - Jason Rasmussen

Saunders1986
Regular Member
Posts: 17
Joined: Sat Jul 07, 2018 10:30 pm

Re: center console ?, also, service manual needed

Post by Saunders1986 » Tue Oct 02, 2018 9:19 pm

crownedking wrote:
Mon Oct 01, 2018 11:44 am
it looks better if you get the base LX face plate.
Agreed, but it’s also very expensive.

uzi4life991
New Member
Posts: 3
Joined: Thu Sep 06, 2018 9:14 pm
Vehicle: 2013 3.5l ecoboost

Re: center console ?, also, service manual needed

Post by uzi4life991 » Wed Oct 03, 2018 1:14 pm

What do people mean by lx face plate I found a radio faceplate from a base taurus sel can find them normally for 50-90$ easily on eBay often. It looks slightly longer with a little indentation towards the bottom Is this the LX faceplate mentioned?
https://rover.ebay.com/rover/0/0/0?mpre ... 2722086088
Will this work to solve the gap issue?

Saunders1986
Regular Member
Posts: 17
Joined: Sat Jul 07, 2018 10:30 pm

Re: center console ?, also, service manual needed

Post by Saunders1986 » Wed Oct 03, 2018 4:16 pm

I was mistaken, looks like that faceplate from base model is what crownedking was referring too, I thought he was suggesting another trim part that can be purchased.

crownedking
Regular Member
Posts: 74
Joined: Fri Mar 18, 2016 1:03 pm
Location: MN
Contact:

Re: center console ?, also, service manual needed

Post by crownedking » Thu Oct 04, 2018 7:07 pm

uzi4life, yes it will fit and close the gab, but you need to retain the a/c temp fan part from the police console and use tubing under the console to get air flow. I've done two like this and they look great.
DON'T buy from paid PI mod sites, stay away from dealer programming! message me for help or questions.

"If you believe you can figure it out on your own then by all means do feel free to do so. I have nothing against people who want to do it on their own. I am not aware of anyone else that has done it though." - jmr061 - Jason Rasmussen

Post Reply